Junbiao Lai
Junbiao Lai
Research & Technology Development, SKF Group
Verified email at
Cited by
Cited by
3-D Schapery representation for non-linear viscoelasticity and finite element implementation
J Lai, A Bakker
Computational mechanics 18 (3), 182-191, 1996
Analysis of the non-linear creep of high-density polyethylene
J Lai, A Bakker
Polymer 36 (1), 93-99, 1995
An integral constitutive equation for nonlinear plasto‐viscoelastic behavior of high‐density polyethylene
J Lai, A Bakker
Polymer Engineering & Science 35 (17), 1339-1347, 1995
A numerical study of crack-tip plasticity in glassy polymers
J Lai, E Van der Giessen
Mechanics of Materials 25 (3), 183-197, 1997
Investigation on the mechanisms of white etching crack (WEC) formation in rolling contact fatigue and identification of a root cause for bearing premature failure
J Lai, K Stadler
Wear 364, 244-256, 2016
The fatigue limit of bearing steels–Part I: A pragmatic approach to predict very high cycle fatigue strength
J Lai, T Lund, K Rydén, A Gabelli, I Strandell
International Journal of Fatigue 38, 155-168, 2012
Effects of microstructure and surface roughness on the fatigue strength of high-strength steels
J Lai, H Huang, W Buising
Procedia Structural Integrity 2, 1213-1220, 2016
The fatigue limit of bearing steels–Part II: Characterization for life rating standards
A Gabelli, J Lai, T Lund, K Rydén, I Strandell, GE Morales-Espejel
International journal of fatigue 38, 169-180, 2012
A review: the dilemma with premature white etching crack (WEC) bearing failures
K Stadler, J Lai, R Vegter
Bearing Steel Technologies: 10th Volume, Advances in Steel Technologies for …, 2015
Non-linear time-dependent deformation behaviour of high-density polyethylene.
J Lai
The stress intensity factor and stress concentration for a finite plate with a single crack emanating from a hole
J Lai, J Schijve
Engineering fracture mechanics 36 (4), 619-630, 1990
A comparison of Mode III threshold under simple shear and RCF conditions
MG Tarantino, S Beretta, S Foletti, J Lai
Engineering fracture mechanics 78 (8), 1742-1755, 2011
Case depth and static capacity of surface induction-hardened rings
J Lai, P Ovize, H Kuijpers, A Bacchettto, S Ioannides
ASTM International, 2009
Mechanical modeling of coupled plasticity and phase transformation effects in a martensitic high strength bearing steel
S Hazar, B Alfredsson, J Lai
Mechanics of Materials 117, 41-57, 2018
Propagation of physically short cracks in a bainitic high strength bearing steel due to fatigue load
B Alfredsson, M Öberg, J Lai
International Journal of Fatigue 90, 166-180, 2016
Dark etching regions under rolling contact fatigue: a review
S Echeverri Restrepo, SW Ooi, P Yan, P Andric, RH Vegter, J Lai
Materials Science and Technology 37 (4), 347-376, 2021
An investigation of a hole-edge crack problem by a combined complex variable and least square method
L Junbiao, Z Xing, J Schijve
Engineering fracture mechanics 39 (4), 713-737, 1991
Low temperature creep in a high strength roller bearing steel
B Alfredsson, IL Arregui, J Lai
Mechanics of Materials 100, 109-125, 2016
Fluid-crack interaction in lubricated rolling-sliding contact
J Lai, E Ioannides, J Wang
International Joint Tribology Conference 43369, 437-439, 2008
Non-linear creep and recovery behaviour of high-density polyethylene
J Lai, A Bakker
Scripta metallurgica et materialia 28 (11), 1447-1452, 1993
The system can't perform the operation now. Try again later.
Articles 1–20